DIY Glitter Resin Ring Holder: A Step-by-Step Tutorial

Updated at: 13/05/2025

Are you tired of your rings getting tangled or lost in a jewelry box? Do you love crafting and adding a touch of sparkle to your everyday life? Then this DIY glitter resin ring holder is the perfect project for you! This stunning and practical accessory is surprisingly easy to make, requiring only a few readily available materials and a little bit of patience. Forget expensive, mass-produced holders; create a unique piece that reflects your personal style and adds a touch of glamorous organization to your vanity. The shimmering glitter embedded within the resin creates a truly captivating effect, turning a functional item into a beautiful decorative piece.

This tutorial will guide you through each step of creating your own dazzling glitter resin ring holder, from preparing your mold to adding the finishing touches. Let's dive into the step-by-step process and unleash your inner crafter!

Preparation and Safety Guidelines

Tools Needed
  • Resin
  • Glitter (chunky and fine)
  • Mold (flower shaped)
  • Mixing cups
  • Mixing sticks
  • Alcohol
  • Torch or lighter
Safety Guidelines
  • Always work in a well-ventilated area. Resin fumes can be irritating and harmful if inhaled.
  • Wear gloves and eye protection throughout the entire process to prevent skin and eye irritation from resin and glitter.
  • Dispose of resin and glitter waste responsibly according to local regulations. Never pour resin down the drain.

Step-by-Step Instructions

  1. Prepare the Resin

    • Measure 3 ounces of resin (using water for accurate measurement)
    • Divide resin into two portions for different glitters.
    Divide resin into two portions for different glitters.Divide resin into two portions for different glitters.
    Prepare the Resin

  2. Add Chunky Glitter and Resin

    • Add chunky glitter to the center and edges of the mold.
    • Pour resin into the mold, ensuring it reaches all areas.
    Pour resin into the mold, ensuring it reaches all areas.Pour resin into the mold, ensuring it reaches all areas.
    Add Chunky Glitter and Resin

  3. Add Fine Glitter and Resin

    • Add fine glitter to the remaining resin and pour into the mold.
    Add fine glitter to the remaining resin and pour into the mold.
    Add Fine Glitter and Resin

  4. Finish and Cure

    • Dome the top of the resin to minimize trimming later.
    • Spray with alcohol to remove bubbles and use a torch to pop any remaining bubbles.
    • Let the resin cure overnight.
    Let the resin cure overnight.Let the resin cure overnight.Let the resin cure overnight.
    Finish and Cure

  5. Unmold the Ring Holder

    • Unmold the resin ring holder.
    Unmold the resin ring holder.
    Unmold the Ring Holder

Read more: Ultimate Guide to Making Inlay Rings with Bentwood Ring Supplies

Tips

  • Use water to accurately measure resin before mixing.
  • Domed resin needs less trimming.
  • Mix slightly more resin than needed to easily dome the top.
  • Alcohol spray helps remove bubbles effectively.

Common Mistakes to Avoid

1. Air Bubbles in the Resin

Reason: Improper mixing or pouring techniques can trap air bubbles, creating an uneven and unprofessional finish.
Solution: Gently heat the resin mixture to reduce viscosity and allow trapped air to escape, then slowly pour and use a toothpick to pop any remaining bubbles.

2. Uneven Resin Distribution

Reason: Pouring resin too quickly or in one spot can lead to uneven thickness and potentially even cracks in the finished ring holder.
Solution: Pour the resin slowly and evenly to ensure consistent thickness throughout the mold.

3. Glitter Settling

Reason: Heavy glitter can sink to the bottom of the mold before the resin cures completely.
Solution: Mix the glitter thoroughly with the resin and consider using a slightly thicker resin to help keep the glitter suspended.

FAQs

What type of resin is best for making a glitter resin ring holder?
For this project, epoxy resin is recommended. It's known for its clarity, durability, and ability to hold glitter evenly. Ensure you choose a resin specifically designed for jewelry making, as these often have lower viscosity and cure to a harder finish.